GE GDF530PGMCC Instalační manuál stáhnout pdf (Strana 13)

Dishwasher Installation

CONNECT POWER SUPPLY

If a power cord with plug is already installed

proceed to Step 18.

In this step you will need the junction box cover and the

#10 Hex head screw from the screws set aside in Step 1.

• Secure house wiring to the back of the junction box

with a strain relief as shown in the MATERIALS YOU

WILL NEED section.

• Locate the 3 dishwasher wires, (white, black and green)

with the stripped ends coming out of the AC jumper. Use

UL-listed wire nuts of appropriate size to connect incoming

ground to green, white to white and black to black.

• Install the junction box cover using #10 hex head screw.

Check to be sure that wires are not pinched under the

cover and that all wire nuts are inside the cover.

• Make sure that the junction box cover is resting on

the mounting bracket.

To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires

are not pinched or damaged, the house wiring is attached

to the junction box bracket through a strain relief, and

all electrical connections made at the time of install (wire

nuts) are contained inside of the junction box cover.

WARNING

STEP 17

PRETEST CHECKLIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your Warranty.

• Check to be sure power is OFF.

• Open door and remove all foam and paper

packaging.

• Locate the Owner’s Manual set aside in Step 1.

• Read the Owner’s Manual for operating instructions.

• Check door opening and closing. If door does not

open and close freely, check for proper routing of

spring cable over pulley. If door drops or closes

when released, adjust spring tension. See Step 2.

• Check to be sure that wiring is secure under the

dishwasher, not pinched or in contact with door

springs or other components. See Step 17.

• Check door alignment with tub. If door hits tub, level

dishwasher. See Step 13.

• Check door alignment with cabinet. If door hits

cabinet, reposition dishwasher. See Step 12.

• Pull lower rack out, about halfway. Check to be sure

it does not roll back or forward on the door. If the

rack moves, adjust leveling legs. See Step 13.

• Check that door spring does not contact water line,

fill hose, wiring or other components. See Step 12.

• Verify water supply and drain lines are not kinked

or in contact with other components. Contact with

motor or dishwasher frame could cause noise.

• Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must be

between 120°F and 140°F. A minimum of 120°F

temperature is required for best wash performance.

See PREPARE HOT WATER LINE section.

• Add 2 quarts of water to the bottom of the

dishwasher to lubricate the pump seal.

• Turn on water supply. Check for leaks. Tighten

connections if needed.

• Remove protective film if present from the control

panel and door.

• Check that tub trim does not contact the door.

STEP 18

Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador deberá realizar un

control para asegurar que los cables no estén pellizcados

ni dañados, que el cableado del hogar esté conectado a la

ficha de la caja de empalmes a través de un amortiguador

de refuerzo, y que todas las conexiones eléctricas realizadas

en el momento de la instalación (tuercas para cables) estén

dentro de la tapa de la caja de empalmes.

ADVERTENCIA

NOTE: All ground screws, brackets and wires must remain intact.

Junction

Box Cover

Ground

(Green)

NOTE:

Do not

remove

the

Junction

Box

Bracket.

AC Power

Connector

Junction

Box

Bracket

Black

White

Ground

Screws

Strain

Relief

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 31 32

Komentáře k této Příručce

Žádné komentáře

GE GDF530PGMCC Instalační manuál Strana 13

Komentáře k této Příručce

Související produkty a manuály pro Myčky nádobí GE GDF530PGMCC