GE GPF325W Instalační manuál stáhnout pdf

Installation

Instructions

GPF325 SERIES KITS

1/4" Custom Dishwasher Door

and Access Panel Kit

GPF325A, Almond Trim Kit

GPF325B, Black Trim Kit

GPF325C, Bisque Trim Kit

GPF325W, White Trim Kit

WARNING:

To prevent electric shock, disconnect electrical

power supply to dishwasher before changing

panels. Do not operate dishwasher while

changing panels or when lower access panel

assembly is removed.

TOOLS AND MATERIALS

REQUIRED:

• 1/4" socket driver

• Phillips screwdriver

• Electric drill

• 1/8" drill bit

• Masking tape

• Safety glasses

• Center punch

• Gloves to protect against sharp edges

The GPF325 trim kits provide for the installa-

tion of 1/4" thick custom door and access

panels.

KIT INCLUDES:

• Left, right and bottom door trim

• Top and bottom access panel trim

• Color matched screws

Before you begin

Read these instructions completely

and carefully.

IMPORTANT – Save these instructions

for local inspector’s use.

IMPORTANT – Observe all governing

codes and ordinances.

Note to Installer – Be sure to leave these

instructions with the Consumer.

Note to Consumer – Keep these instructions

with your Owner’s Manual for future

reference.

STOP

1 CUT 1/4" THICK CUSTOM

PANELS TO SIZE

• Cut door panel and access panel to the

dimensions shown.

NOTE: The trim provided will conceal the cut

edges of the panels.

1/4" Thick

Door Panel

23-9/16"

3-11/16"

18-7/8"

1/4" Thick Access Panel

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Instructions

InstallationInstructionsGPF325 SERIES KITS1/4" Custom Dishwasher Doorand Access Panel KitGPF325A, Almond Trim KitGPF325B, Black Trim KitGPF325C,

Strany 2 - PANEL DE ACCESO INFERIOR

2AB• Slide “Z” shaped trim under theescutcheon.• Place bottom trim against the bottomof the door panel and drive centerscrew, then left and right scre

Strany 3

F• Center punch and drill holes through theholes in the side trim and into the dishwasherdoor.• Secure the trim to the door with colormatched screws p

Strany 4 - Spring Kit MUST BE installed

4 INSTALL CUSTOMACCESS PANEL• Place 1/4" custom panel in position on theaccess panel assembly. Use masking tape tohold in position.• Loosely, ins

Strany 5 - Instrucciones

Panel de puerta conespesor de 1/4 de pulg. (6 mm)23-9/16 pulg. (60 cm)3-11/16 pulg. (94 mm)18-7/8 pulg.(48 cm)Panel de acceso con espesorde 1/4 de pul

Strany 6 - PERSONALIZADO

Moldura en “Z”2AB• Deslice la moldura en “Z” bajo lalámina.• Ponga la moldura inferior contra laparte inferior del panel de puerta,atornille primero e

Strany 7

Fije lasmoldurasa cada ladodel panelpersonalizadoTaladreorificiosy atornillelos tornillosF• Marque con el punzón de centros la posiciónde los orificio

Strany 8 - 2 tornillos

18-7/8 pulg.(48 cm)Separación mínimade 1/4 de pulg.23-9/16 pulg.(60 cm)PaneldecorativoPanel conespesorde 1/4 depulg. (6 mm)Separaciónmínima de1/8 de p