GE JX7230DFBB Instalační manuál stáhnout pdf

PART QUANTITY

Trim Frame 1

Bottom Duct 1

Top Bracket 1

Phillips Round-Head

Screws

(21 or 22 required

for installation)

Phillips Flat-Head 5

Screws (4 required

for installation)

Anti-Tip Bracket 1

Bottom Bracket 1

Template 1

PARTS INCLUDED

Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Installation Built-In Trim Kits

Instructions

JX7227 and JX7230

Read these instructions completely and carefully.



IMPORTANT – Save these

instructions for local inspector’s use.



IMPORTANT – Observe all

governing codes and ordinances.

 Note to Installer – Be sure to leave these

instructions with the Consumer.

 Note to Consumer – Keep these instructions for

future reference.

For easier installation and personal safety, we recommend

that two people install this microwave oven.

 Unplug the microwave oven before attempting

installation of this kit.

BEFORE YOU BEGIN

 Skill level – Installation of this appliance requires basic

mechanical and electrical skills.

 Completion time – 1-3 hours

 Proper installation is the responsibility of the installer.

 Product failure due to improper installation is not

covered under the Warranty.

 This kit is UL listed for installation alone or over

any General Electric/Hotpoint single electric wall oven.

TOOLS YOU WILL NEED

#2 Phillips

screwdriver

Pencil

Tape measure

Awl or punch

Drill with

ø64” bit or #35

FOR YOUR SAFETY:

WARNING – Before beginning the

installation, switch power off at service panel and lock

the service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the

service panel.

Scissors (optional)

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Instructions

PART QUANTITY Trim Frame 1 Bottom Duct 1 Top Bracket 1 Phillips Round-Head 24 Screws (21 or 22 required for installation) Phillips Flat-Head

Strany 2 - Installation Instructions

2CUTOUT DIMENSIONS* Min. depth with receptacle outside cabinet 191ø2” Min. depth with receptacle inside cabinet 22”Installation InstructionsModels 27

Strany 3

3Installation InstructionsINSTALL THE ANTI-TIP BRACKET3 Draw a line on the cutout floor at the center of the cutout, and extend the line 1ø2”down th

Strany 4

4Installation Instructions Place the top bracket on the top of the microwave oven, with the tabs on the top and sides of the bracket fitting squarely

Strany 5 - ANTES DE COMENZAR

PIEZA CANTIDAD Estructura Ajustable 1 Conducto Inferior 1 Soporte Superior 1 Tornillos Phillips con 24 Cabeza Redonda (Se requieren 21 o 22

Strany 6 - Instrucciones de Instalación

2DIMENSIONES DEL RECORTE3URIXQGLGDGPtQLPDFRQHOUHFHSWiFXORIXHUDGHOJDELQHWHòµ3URIXQGLGDGPtQLPDFRQHOUHFHSWiFXORGHQWURGHOJDELQHWH

Strany 7

3Instrucciones de InstalaciónINSTALE EL SOPORTE ANTIVOLCADURAS3 Dibuje una línea sobre el piso del recorte, específicamente en el centro de la misma,

Strany 8

4Instrucciones de Instalación Coloque el soporte superior en la parte superior del horno microondas, con las lengüetas sobre la parte superior y los

Komentáře k této Příručce

Žádné komentáře

GE JX7230DFBB Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro ne GE JX7230DFBB. GE JX7230DFBB Installation Instructions Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro ne GE JX7230DFBB