GE GFK-0726B Uživatelský manuál

GE Fanuc AutomationState Logic ProductsState Logic ProcessorFor Series 90 -30 PLCUser’s GuideGFK-0726B March 1998

11-2 State Logic Processor for Series 90–30 PLC User’s Guide – March 1998GFK-0726B-Physical DescriptionThe SLP occupies a single slot in the Series 90

11-3GFK-0726B Chapter 1 State Logic Processor Descriptiona45127OKBDOKRESTARTBATTERYOPENREPLACEMENTBATTERYCONNECTORPORTS1 AND 2SLP 300CURRENTLYINSTALL

11-4 State Logic Processor for Series 90–30 PLC User’s Guide – March 1998GFK-0726B-Operational DescriptionThe State Logic Processor (SLP) uses areas i

2section level 1 1figure bi level 1 table_big level 1 2-1GFK-0726BChapter 2 Installation and MaintenanceThis chapter describes how to install the

22-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BConfigurationUse the Logicmaster 90-30 configuration software to ad

22-3GFK-0726B Chapter 2 Installation and MaintenanceBatteryThe State Logic Processor comes with a 3 volt lithium battery (IC697ACC701) to maintainmem

3section level 1 1figure bi level 1 table_big level 1 3-1GFK-0726BChapter 3 TroubleshootingThis chapter provides procedures for diagnosing State

33-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BCommunications Problems with ECLiPS or OnTOP1. Check that the serial

4section level 1 1figure bi level 1 table_big level 1 4-1GFK-0726BChapter 4 Serial CommunicationsSerial communications with the State Logic Proce

44-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BProgramming Serial CommunicationsThe program communicates through tw

GFL–002Warnings, Cautions, and Notesas Used in this PublicationWarningWarning notices are used in this publication to emphasize that hazardous voltage

44-3GFK-0726B Chapter 4 Serial CommunicationsSerial Port SetupThere are several serial port configuration options. Some of these options are set usi

44-4 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BTable 4-1. Serial Port ParametersParameter SettingsBaud Rate 19.2K

44-5GFK-0726B Chapter 4 Serial CommunicationsSerial CableThe State Logic Processor (SLP) is designed to work with two GE Fanuc standard serialcables.

44-6 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BOther Cable OptionsOther cables that work with the SLP are the IBM-A

44-7GFK-0726B Chapter 4 Serial CommunicationsCustom Made CablesIf you want to make your own cable to connect to some serial device, use the drawing o

44-8 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726Ba4509121345678910111213151617181920212223242514RS–232 DTRSHIELDRS–23

5section level 1 1figure bi level 1 table_big level 1 5-1GFK-0726BChapter 5 SpecificationsTable 5-1. Serial Ports 1 RS-232 1 RS-422/485Memory B

55-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BTable 5-3. Firmware SpecificationsTasks 256States Per Task 255Integ

GE Fanuc Automation North America, Inc. GFJ–317CSoftware License AgreementYOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE OPENING

iii GFK-0726BPrefaceContent of this ManualChapter 1. State Logic Processor DescriptionChapter 2. Installation and MaintenanceChapter 3. Troublesho

Contents viiGFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998Chapter 1 State Logic Processor Description 1-1 . . . . . .

Contents viiiGFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998

Contents ixGFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998

1restart lowapp ARestart oddapp: ARestarts for autonumbers that do not restart ineach chapter. figure bi level 1, reset table_big level 1, reset cha