Ge 45132 GE Choice Alert Motion Sensor Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Ge 45132 GE Choice Alert Motion Sensor. GE 45132 GE Choice Alert Motion Sensor User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
45132
Choice
ALERT
Choice
ALERT
Control all Sensors
& accessories from
one location
Wireless Alarm System
Motion
Sensor
User’s Manual
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - User’s Manual

45132ChoiceALERTChoiceALERT™Control all Sensors & accessories from one location™Wireless Alarm SystemMotion SensorUser’s Manual

Strany 2 - Table of Contents

1011However, you can check the Motion Sensor status independently by placing the Control Center in Test mode (see Testing a Sensor on page 7) and trig

Strany 3 - Congratulations

1011WARNING!Risk of personal injury- Prolonged exposure to alarm siren may cause permanent hearing lossBattery Warning!- Remove batteries before s

Strany 4

1213Motion Sensor F.A.Q.’SQ. I bought a new Sensor and the Control Center will not recognize it. Why?A. First, make sure that the battery is new and

Strany 5 - Introduction

1213Sensor.This will cause low battery indication on the Control Center (See pg 10).Q. Why does one of my Zones continually flash?A. This can be caus

Strany 6

1415FCC WarningAny unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal la

Strany 7 - Armed Power

1415WARNINGLimitations of Alarm ProductsThis product should be tested periodically to make sure it is working properly. The product, if used properly,

Strany 8

is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, O

Strany 9

23Important Safeguards 4Introduction 5Assigning a Sensor to a Zone 6-7Testing a Sensor or your system 7-8Installation 8Erasing a Se

Strany 10

23Before connecting or operating the Motion Sensor, please read these instructions carefully and save this manual for future reference.Congratulations

Strany 11

45Important safeguardsPreCautions1. Do not attempt to disassemble the Motion Sensor, unless described in the user’s manual. There are no user servicea

Strany 12 - Motion Sensor F.A.Q.’S

45IntroductionThe Motion Sensor is designed to be used indoors or out. When mounted properly it can monitor large or open areas such as entrances, liv

Strany 13 - (see pg.9 in manual)

67Preparing the Motion Sensor for InstallationThe Motion Sensor consists of 2 parts – The Sensor (Transmitter) and the wall mount. Before installing,

Strany 14

67 - To activate the Motion Sensor, press the Learn button located inside the battery compartment, or if mounted wave your hand in front

Strany 15

89 Step 3 - Set the Notification Mode to switch ‘Alert’ position and begin activating Sensors one at a time. Note: The sensor has a LED that flashes

Strany 16

89Erasing the Sensor from a ZoneNote: If you need to remove the Sensor from a Zone, the system will erase the entire Zone, so any other Sensors will n

Komentáře k této Příručce

Žádné komentáře