Installation InstructionsBuilt-In DishwasherIf you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website at: GEApplia
Dishwasher Installation PUSH DISHWASHER INTO FINAL POSITION (CONT.)• Check dishwasher alignment prior to opening dishwasher door to prevent panel da
Dishwasher Installation11 POSITION DISHWASHER, SECURE TO COUNTERTOP OR CABINETIn this step you will need the 2 Phillips special head screws from the
CONNECT DRAIN LINE (CONT.)• Connect drain line to air gap, waste tee or disposer using the previously determined method. Secure hose with a screw-ty
Dishwasher Installation13 CONNECT POWER SUPPLYIf a power cord with plug is already installed proceed to Step 18. In this step you will need the junct
Dishwasher Installation14 DISHWASHER WET TEST• Turn on power supply or plug power cord into outlet, if equipped.• Select a cycle to run and push th
Dishwasher Installation15 LITERATURE• Be sure to leave complete literature package, these Installation Instructions and product samples and/or co
NOTE: Product improvement is a continuing endeavor at GE Appliances. Therefore, materials, appearance and specifications are subject to change without
Directives d’installation Lave-vaisselle encastré Pour toute question, composez le 800.561.3344 ou visitez notre site web: electromenagersge.caPOUR
Préparation pour l’installation2PIÈCES FOURNIES DANS L’EMBALLAGE :• Couvercle de la boîte de jonction et vis à tête hexagonale n° 10• Collier• Bo
PRÉPARATION DE L’OUVERTURE DANS LES ARMOIRES• L’ouverture dans les armoires doit mesurer au moins 61,0 cm (24 po) de largeur et de profondeur, et envi
PARTS SUPPLIED IN INSTALLATION PACKAGE:• Junction box cover and #10 hex-head screw• Hose clamp• Drain hose (approximately 58” long)• Drain hose h
PRÉPARATION DU CÂBLAGE ÉLECTRIQUEAlimentation électrique• Cet appareil doit être alimenté par un courant de 120 V et +]HWEUDQFKpjXQFLUFXLW
5Préparation pour l’installationPRÉPARATION DE L’ALIMENTATION EN EAU CHAUDEREMARQUE: GE Appliances recommande l’utilisation d’un tuyau en cuivre pour
Installation du lave-vaisselle6 ENLÈVEMENT DU PANNEAU INFÉRIEURPassez cette étape si la plinthe n’est pas préinstallée sur l’appareil. Sur certains m
POSITIONNEMENT DE LA CONDUITE D’EAU ET DE L’ALIMENTATION ÉLECTRIQUE• Positionnez la conduite d’alimentation en eau et le câblage de la résidence sur
INSTALLATION DES MOULURES (certains modèles)Sautez cette étape si aucune moulure n’est fournie avec le lave-vaisselle. Au cours de cette étape, vou
9Installation du lave-vaisselle INSTALLATION DES SUPPORTS DE MONTAGEVous aurez besoin des supports de montage et de deux (2) vis à tête hexagonale no
MISE DE NIVEAU DU LAVE-VAISSELLE (SUITE)• Enlevez le panier inférieur et placez un niveau sur la porte et sur le rail du panier inférieur, comme ind
11Installation du lave-vaisselle FIXATION DU LAVE-VAISSELLE AU-DESSOUS DU COMPTOIR OU AUX CÔTÉS DES ARMOIRESAu cours de cette étape, vous aurez besoi
RACCORDEMENT DU BOYAU DE VIDANGE (SUITE)• Branchez le boyau de vidange à la coupure anti-refoulement, au raccord en T ou au broyeur à déchets jO¶DL
Installation du lave-vaisselle13 BRANCHEMENT DE L’ALIMENTATION ÉLECTRIQUESi un cordon d’alimentation pourvu d’une fiche est déjà installé sur l’appar
PREPARE DISHWASHER ENCLOSURE• The rough cabinet opening must be at least 24” deep, 24” wide and approximately 34-1/2” high from floor to underside of
Installation du lave-vaisselle ESSAI DU LAVE-VAISSELLE AVEC DE L’EAU• Rétablissez l’alimentation électrique ou si l’appareil est doté d’un cordon d
Installation du lave-vaisselle15 INSTALLATION DU PANNEAU INFÉRIEUR• Appuyez le panneau inférieur contre les pieds de nivellement du lave-vaisselle.•
NOTE: Chez GE Appliances, nous nous efforçons continuellement d’améliorer les produits. Par conséquent, les matériaux, l’aspect et les caractéristique
Installation PreparationFor models equipped with power cord: Do not modify the plug provided with the appliance; if it will not fit the outlet, have a
Water Line Connection• If using a flexible braided supply hose, label the hose with the installation date to use as reference. Flexible braided hoses,
ToekickRemove 2Toekick Screws REMOVE TOEKICK Skip this step if the toekick is not pre-installed on the unit. On some models the toekick is packaged s
STEP 7 POSITION WATER LINE AND HOUSE WIRING• Position water supply line and house wiring on the floor of the opening to avoid interference with base
INSTALL TRIM PIECES (on some models)Skip this step if trim is not supplied with the dishwasher.In this step you will need the trim pieces set aside
Dishwasher Installation9 INSTALL MOUNTING BRACKETSYou will need the mounting brackets and 2 #8 hex-head screws set aside in Step 1.You must install t
Komentáře k této Příručce