BEFORE YOU BEGINRead these instructions completely and carefully. IMPORTANT – Save these instructions for local electrical inspector’s use. IMPORT
CONNECTING AN ELECTRIC DRYER (cont.)Installation InstructionsELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS- Fire HazardWARNINGUse a new UL-lis
Installation InstructionsCONNECTING DRYER USING 3-WIRE CONNECTION3-wire ConnectionNot for use in Canada.DO NOT use for Mobile Home Installations.NOT f
Phillips-head screwdriver Duct tape or duct clamp 5LJLGRU8/OLVWHGflexible metal 4” (10.2 cm) duct Drill with 1/8” drill bit (for bottom vent
Installation InstructionsUsing exhaust longer than specified length will: Increase the drying times and the energy cost. 5HGXFHWKHGU\HUOLIH
EXHAUSTING THE DRYER (cont.)Installation InstructionsBEFORE YOU BEGIN 5HPRYHDQGGLVFDUGH[LVWLQJSODVWLFRUPHWDOIRLOduct and replace with UL-lis
15Installation InstructionsSIDE OR BOTTOM VENTINGDryer Exhaust to right of cabinet for Electric models only.Dryer Exhaust to left of cabinet for Gas a
EXHAUSTING THE DRYER (cont.)NEVER LEAVE THE BACK OPENING WITHOUT THE PLATE. (Kit WE1M454.)Installation InstructionsSIDE OR BOTTOM VENTING (cont.)Conne
Lea estas instrucciones por completo y con detenimiento. IMPORTANTE – Guarde estas instrucciones para el uso de inspectores eléctricos locales. I
4,4” (11,2 cm)2Instrucciones de instalaciónIncline la secadora de costado y saque los soportes de HVSXPDGHHPEDODMHWLUDQGRGHORVFRVWDGRV\TXLWiQ
3Instrucciones de instalaciónREQUERIMIENTOS PARA INSTALACIÓN EN NICHOS O ARMARIOSINSTALACIÓN EN CASAS MÓVILES O PREFABRICADAS- Riesgo de explosiónADV
4.4” (11.2 cm)5.4” (13.7 cm)Installation InstructionsTilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking
4Instrucciones de instalaciónCÓMO CONECTAR MANGUERAS DE ENTRADA(sólo para los modelos de secadoras de vapor)CÓMO CONECTAR MANGUERAS DE ENTRADAPara pr
CÓMO CONECTAR UNA SECADORA A GAS (si se cuenta con una secadora eléctrica, saltear este paso) Llaves ajustables de 10” (2) Llave para tubos de 8”
CÓMO CONECTAR UNA SECADORA A GAS (cont.)6Instrucciones de instalaciónREQUERIMIENTOS DE GASCONEXIÓN DE SUMINISTRO DE GAS DE LA SECADORASUMINISTRO DE G
Instale una toma a rosca de 1/8” NPT HQODYiOYXODGHDSDJDGRGHODWXEHUtDGHJDVde la secadora para controlar la presión de gas en la entrada.
Instrucciones de instalación8PRUEBA DE PÉRDIDASAbra la YiOYXOD de gasCONEXIÓN ELÉCTRICA INFORMACIÓN SOBRE LAS SECADORAS A GAS (cont.)La secadora debe
Codo de metal de µGHGLiPHWUR Alivio de tensión de 3/4” (reconocido por UL) Abrazaderas de tubería de 4” (2) o abrazaderas de resorte de 4” (2)
10CÓMO CONECTAR UNA SECADORA ELECTRICA (cont.)Instrucciones de instalaciónCONEXIÓN ELÉCTRICA INFORMACIÓN SOBRE LAS SECADORAS ELÉCTRICAS ADVERTENCIA- R
Instrucciones de instalación 11CÓMO CONECTAR LA SECADORA USANDO UNA CONEXIÓN DE 4 CABLES (DEBE UTILIZARSE EN INSTALACIONES DE CASAS RODANTES)NOTA: Des
Destornillador phillips Cinta aislante o abrazaderas de tubería Conducto de metal de 4” (10,2 cm) flexible o rígido listado UL Perfore con una br
Instrucciones de instalaciónAl utilizar una salida de mayor longitud a la especificada se: ,QFUHPHQWDUiQORVWLHPSRVGHVHFDGR\HOFRVWRde energía
Installation InstructionsREQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATIONMOBILE OR MANUFACTURED HOME INSTALLATION3- Explosion HazardWARNINGKeep flammabl
Lado de la paredLado de la secadoraConducto de transiciónInstrucciones de instalación14ANTES DE COMENZAR4XLWHODVSHOXVDVGHODDEHUWXUDGHVDOLGD d
Instrucciones de instalación15VENTILACIÓN LATERAL O POR LA PARTE INFERIORLa secadora cuenta con una salida hacia la derecha del gabinete sólo en model
Instrucciones de instalación16VENTILACIÓN LATERAL O POR LA PARTE INFERIOR (cont.)&RQHFWHORVFRGRV\FRQGXFWRVGHPHWDOHVWiQGDUpara completar el
4Installation InstructionsCONNECTING INLET HOSES (for steam dryer models only)CONNECTING INLET HOSES (cont.)7. Using pliers, tighten all the coupling
10” Adjustable wrenches (2) 8” Pipe wrench Slip-joint pliers Flat-blade screwdriver LevelInstallation InstructionsTOOLS YOU WILL NEEDCONNECTING
CONNECTING A GAS DRYER (cont.)Installation InstructionsGAS REQUIREMENTSDRYER GAS SUPPLY CONNECTIONGAS SUPPLY A 1/8” National Pipe Taper thread plugg
Install a 1/8” NPT plugged tapping to the dryer gas line shut-off valve for checking gas inlet pressure. Install a flare union adapter to the plugg
Installation InstructionsTEST FOR LEAKSNever use an open flame to test for gas leaks.Check all connections for leaks with soapy solution or equivalent
Installation InstructionsCONNECTING AN ELECTRIC DRYER (Skip for gas dryers and if your dryer already has a power cord attached)Before making the elect
Komentáře k této Příručce